Common metallic properties

1.Commonly used aluminum alloy for die casting

American Standard ASTM B85-96 United States die-cast aluminum alloy chemical composition table

Alloy grade			Divide
ANSI	ASTM	UNS	Si	Fe	Cu	Mn	Mg	Ni	Zn	Sn	Ti	Impurities (total)	AI
360.0	SG100B	A03600	9.0-10.0	2.0	0.6	0.35	0.40-0.60	0.50	0.50	0.15		0.25	margin
A360.0	SG100A	A13600	9.0-10.0	1.3	0.6	0.35	0.40-0.60	0.50	0.50	0.15		0.25	margin
380.0	SC84B	A03800	7.5-9.5	2.0	3.0-4.0	0.50	0.10	0.50	3.0	0.35		0.50	margin
A380.0E	SC84A	A13800	7.5-9.5	1.3	3.0-4.0	0.50	0.10	0.50	3.0	0.35		0.50	margin
383.0E	SC102A	A03830	9.5-11.5	1.3	2.0-3.0	0.50	0.10	0.30	3.0	0.15		0.50	margin
384.0E	SC114A	A03840	10.5-12.0	1.3	3.0-4.5	0.50	0.10	0.50	3.0	0.35		0.50	margin
390.0	SC174A	A03900	16.0-18.0	1.3	4.0-5.0	0.10	0.45-0.65		0.10		0.20	0.20	margin
B390.0	SC174B	A23900	16.0-18.0	1.3	4.0-5.0	0.50	0.45-0.65	0.10	1.5		0.10	0.20	margin
392.0	S19	A03920	18.0-20.0	1.5	0.40-0.80	0.20-0.60	0.80-1.20	0.50	0.50	0.30	0.20	0.50	margin
413.0	S12B	A04130	11.0-13.0	2.0	1.0	0.35	0.10	0.50	0.50	0.15		0.25	margin
A413.0	S12A	A14130	11.0-13.0	1.3	1.0	0.35	0.10	0.50	0.50	0.15		0.25	margin
C433.0	S5C	A34430	4.5-6.0	2.0	0.6	0.35	0.10	0.50	0.50	0.15		0.25	margin
518.0	G8A	A05180	0.35	1.8	0.25	0.35	7.5-8.5	0.15	0.15	0.25		0.25	margin

Eu standard EN1706:1998 EU table of chemical composition and mechanical properties of die-cast aluminium alloys

Alloy grade	Chemical composition										The tensile strength is minimum Mpa	The yield strength Mpa is minimum	The elongation of % is minimum	The Brinell hardness HB is the smallest
Designation	Si	Fe	Cu	Mn	Mg	Ni	Zn	Pb	Sn	Ti
ENAC-43400	9.0-11.0	0.45-0.9	0.08	0.55	0.20-0.50	0.15	0.15	0.15	0.05	0.15	240	140	1	70
ENAC-44300	10.5-13.5	0.45-0.9	0.08	0.55			0.15			0.15	240	130	1	60
ENAC-44400	8.0-11.0	0.55	0.08	0.50	0.10	0.05	0.15	0.05	0.05	0.15	240	120	2	55
ENAC-46000	8.0-11.0	0.6-1.1	2.0-4.0	0.55	0.15-0.55	0.55	1.2	0.35	0.25	0.2	240	140	<1	80
ENAC-46100	10.0-12.0	0.45-1.0	1.5-2.5	0.55	0.30	0.45	1.7	0.25	0.25	0.2	240	140	<1	80
ENAC-46200	7.5-9.5	0.8	2.0-3.5	0.15-0.65	0.15-0.55	0.35	1.2	0.25	0.15	0.2	240	140	1	80
ENAC-46500	8.0-11.0	0.6-1.2	2.0-4.0	0.55	0.15-0.55	0.55	3.0	0.35	0.25	0.20	240	140	<1	80
ENAC-47100	10.5-13.5	0.6-1.1	0.7-1.2	0.55	0.35	0.30	0.55	0.20	0.10	0.15	240	140	1	70
ENAC-51200	2.5	0.45-0.9	0.10	0.55	8.0-10.5	0.10	0.25	0.10	0.10	0.15	200	130	1	70

National Standard of the People’s Republic of China – Chemical composition and mechanical properties of aluminum alloy GB/T 15115-94 die-cast aluminum alloy

No.

Alloy grade

Chemical composition %

Mechanical function (no less)

Alloy designation

Si

Cu

Mn

Mg

Fe

Ni

Ti

Zn

Sn

Pb

Al

Tensile strength 6ЪN/mm2

Elongation δ/%(Lo=50)

Brinell hardness HB5/250/30

1

YZAISil2

YL102

10.0-13.0

≤0.6

≤0.6

≤0.05

≤1.2

≤0.3

margin

220

2

60

2

YZAISi10Mg

YL104

8.0-10.5

≤0.3

0.2-0.5

0.17-0.30

≤1.0

≤0.3

≤0.05

≤0.01

margin

220

2

70

3

YZAISil2Cu2

YL108

11.0-13.0

1.0-2.0

0.3-0.9

0.4-1.0

≤1.0

≤0.05

≤1.0

≤0.05

≤0.01

margin

240

1

90

4

YZAISi9 Cu4

YL112

7.5-9.5

3.0-4.0

≤0.5

≤0.3

≤1.2

≤0.5

≤1.2

≤0.1

≤0.1

margin

240

1

85

5

YZAISillCu3

YL113

9.6-12.0

1.5-3.5

≤0.5

≤0.3

≤1.2

≤0.5

≤1.0

≤0.1

≤0.1

margin

230

1

80

6

YZAISil7Cu5Mg

YL117

16.0-18.0

4.0-5.0

≤0.5

0.45-0.65

≤1.2

≤0.1

≤0.1

≤1.2

margin

220

＜1

7

YZAIMg5Sil

YL302

0.8-1.3

≤0.1

0.1-0.4

4.5-5.5

≤1.2

≤0.2

≤0.2

margin

220

2

70

Chemical composition and mechanical properties of die-cast zinc alloy according to the National standard of the People’s Republic of China

NO.	Alloy grade	Alloy designation	Chemical composition，%
			Main component				Impurity content (no more than)
			Al	Cu	Mg	Zn	Fe	Pb	Sn	Cd
1	ZZnA14Y	YX040	3.5-4.3	0.25	0.02-0.06	margin	0.1	0.005	0.003	0.004
2	ZZnA14CU1Y	YX041	3.5-4.3	0.75-1.25	0.03-0.08	margin	0.1	0.005	0.003	0.004
3	ZZnA14CU3Y	YX043	3.5-4.3	2.5-3.0	0.02-0.06	margin	0.1	0.005	0.003	0.004
Mechanical property
Tensile strength6Ъ(N/mmˉ2)		Elongation δ/%Lo=50	Brinell hardnessHB5/250/30
250		1	80
270		2	90
320		2	95

Japanese Industrial Standard JIS H5302:2000

Chemical Composition of Japanese Die-Cast Aluminum Alloys

JIS Grade	ISO Grade	Cu	Si	Mg	Zn	Fe	Mn	Ni	Sn	Pb	Ti	Al
ADC1	—	≤1.0	11.0–13.0	≤0.3	≤0.5	≤1.3	≤0.5	≤0.1	—	—	—	Bal.
ADC1	CA1-Si12CuFe	≤1.2	11.0–13.5	≤0.3	≤0.5	≤1.3	≤0.5	≤0.3	≤0.1	≤0.2	≤0.2	Bal.
ADC2	Al-Si12Fe	≤0.1	11.0–13.5	≤0.1	≤0.1	≤1.3	≤0.5	≤0.1	≤0.05	≤0.1	≤0.2	Bal.
ADC3	—	≤0.6	9.0–10.0	0.4–0.6	≤0.5	≤1.3	≤0.3	≤0.5	—	—	—	Bal.
ADC5	—	≤0.2	≤0.3	4.0–8.5	≤0.1	≤1.8	≤0.3	≤0.1	—	—	—	Bal.
ADC6	—	≤0.1	≤1.0	2.5–4.0	≤0.4	≤0.8	0.4–0.6	≤0.1	—	—	—	Bal.
ADC7	Al-Si5Fe	≤0.1	4.5–6.0	≤0.1	≤0.1	≤1.3	≤0.5	≤0.1	≤0.1	≤0.1	≤0.2	Bal.
ADC8	Al-Si6Cu4Fe	3.0–5.0	5.0–7.0	≤0.3	≤2.0	≤1.3	0.2–0.6	≤0.3	≤0.1	≤0.2	≤0.2	Bal.
ADC10	—	2.0–4.0	7.5–9.5	≤0.3	≤1.0	≤1.3	≤0.5	≤0.5	≤0.2	—	—	Bal.
ADC10Z	—	2.0–4.0	7.5–9.5	≤0.3	≤3.0	≤1.3	≤0.5	≤0.5	≤0.2	—	—	Bal.
ADC11	Al-Si8Cu3Fe	2.5–4.0	7.5–9.5	≤0.3	≤1.2	≤1.3	≤0.6	≤0.5	≤0.2	≤0.3	≤0.2	Bal.
ADC12	—	1.5–3.5	9.6–12.0	≤0.3	≤1.0	≤1.3	≤0.5	≤0.5	≤0.2	—	—	Bal.
ADC12Z	—	1.5–3.5	9.6–12.0	≤0.3	≤3.0	≤1.3	≤0.5	≤0.5	≤0.2	—	—	Bal.

---

Japanese Die-Cast Aluminum Alloys Mechanical Properties