This page is a lookup chart, not a tutorial. It reproduces the chemical composition limits for the two GB/T alloy series Chinese foundries quote against — YL (压铸, GB/T 15115) and ZL (gravity and sand casting, GB/T 1173) — so you can check a certificate of analysis against the standard without opening a PDF.
All figures are weight percent, taken from the standard tables. If you are choosing a grade rather than verifying one, the selection logic, the ASTM / EN / JIS cross-reference and the sourcing pitfalls are in Chinese aluminum alloy grades explained (with equivalents).
How to read the tables
- YL is the die casting series (压铸), ZL the gravity and sand casting series (铸铝). The number after the prefix is a sequence number, not a strength rating — a higher number does not mean a better alloy.
- A range such as
9.0~10.0is the target window the foundry aims for. A figure such as1.0maxis a ceiling, usually an impurity limit, not something you add on purpose. /means the element is not specified for that grade; it falls under the general impurity limits of the standard rather than being absent.- Balance is aluminum plus unlisted elements — it is never 100% aluminum.
- A trailing A (ZL101A) marks the tighter-impurity variant of the base grade, normally the one you want if the part is heat treated.
YL series: die casting alloys (GB/T 15115)
High pressure die casting grades. YL102, YL112 and YL113 cover most volume production in China. High silicon buys fluidity and wear resistance at the cost of ductility; copper buys strength at the cost of corrosion resistance. Western equivalents are deliberately not repeated here — the cross-reference table lives in the grades guide, so there is only one place to update when a standard is revised.
| Alloy Code | 丝 | 铁 | 铜 | 百万 | 毫克 | 尼 | 锌 | 锡 | 蒂 | 铅 | Cr | OTHER | Aluminum (Balance) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| YL101 | 9.0~10.0 | 1.0max | 0.6max | 0.35max | 0.45~0.65 | 0.5max | 0.4max | 0.15max | / | 0.1max | / | / | Balance |
| YL102 | 10.0~13.0 | 1.0max | 1.0max | 0.35max | 0.1max | 0.5max | 0.4max | 0.15max | / | 0.1max | / | / | Balance |
| YL104 | 8.0~10.5 | 0.5~0.8 | 0.3max | 0.2~0.5 | 0.3~0.5 | 0.1max | 0.3max | 0.01max | / | 0.05max | / | / | Balance |
| YL112 | 7.5~9.5 | 1.0max | 3.0~4.0 | 0.5max | 0.1max | 0.5max | 2.9max | 0.15max | / | 0.1max | / | / | Balance |
| YL113 | 9.5~11.5 | 1.0max | 2.0~3.0 | 0.5max | 0.1max | 0.3max | 2.9max | / | 0.1max | / | / | / | Balance |
| YL117 | 16.0~18.0 | 1.0max | 4.0~5.0 | 0.5max | 0.5~0.7 | 0.1max | 1.4max | / | 0.2max | 0.1max | / | / | Balance |
| YL302 | 0.35max | 1.1max | 0.25max | 0.35max | 7.6~8.6 | 0.15max | 0.15max | 0.15max | / | 0.1max | / | / | Balance |
Properties, machining behaviour and typical parts for the most-quoted grade are on the ADC12 aluminum alloy page.
ZL series: gravity and sand casting alloys (GB/T 1173)
Lower silicon, tighter impurity control, and the ones that respond to T6. ZL101A, ZL104 and ZL107 are the workhorses; ZL201 and ZL301 trade castability for strength and dimensional stability at temperature.
| Alloy Code | 丝 | 铁 | 铜 | 百万 | 毫克 | 尼 | 锌 | 锡 | 蒂 | 铅 | Cr | OTHER | Aluminum (Balance) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ZL101 | 6.5~7.5 | 0.5max | 0.2max | 0.1max | 0.25~0.45 | 0.1max | 0.1max | 0.01max | 0.15max | 0.05max | / | / | Balance |
| ZL101A | 6.5~7.5 | 0.4max | 0.1max | 0.1max | 0.30~0.50 | 0.05max | 0.1max | 0.01max | 0.15max | 0.03max | / | / | Balance |
| ZL102 | 10.0~13.0 | 0.6max | 0.1max | 0.5max | 0.1max | 0.1max | 0.1max | / | / | 0.05max | / | / | Balance |
| ZL104 | 8.0~10.5 | 0.6max | 0.1max | 0.2~0.5 | 0.17~0.35 | 0.1max | 0.2max | / | 0.1max | 0.05max | / | / | Balance |
| ZL105 | 4.5~5.5 | 0.6max | 1.0~1.5 | 0.4~0.6 | 0.4~0.6 | 0.1max | 0.2max | / | 0.15max | 0.05max | / | / | Balance |
| ZL106 | 7.5~8.5 | 0.6max | 1.0~1.5 | 0.3~0.5 | 0.25~0.45 | 0.1max | 0.1max | / | 0.15max | 0.05max | / | / | Balance |
| ZL107 | 6.5~7.5 | 0.5max | 3.5~4.5 | 0.3max | 0.25~0.45 | 0.1max | 0.1max | / | 0.15max | 0.05max | / | / | Balance |
| ZL108 | 11.0~13.0 | 0.7max | 1.0~2.0 | 0.3~0.9 | 0.4~1.0 | 0.1max | 0.1max | / | 0.1max | 0.05max | / | / | Balance |
| ZL109 | 11.0~13.0 | 0.7max | 0.5~1.5 | 0.5max | 0.8~1.3 | 0.1max | 0.1max | / | 0.2max | 0.05max | / | / | Balance |
| ZL111 | 8.0~10.0 | 0.5max | 1.5~2.5 | 0.3~0.5 | 0.4~0.6 | 0.1max | 0.1max | / | 0.15max | 0.05max | / | / | Balance |
| ZL201 | 0.3max | 0.3max | 4.5~5.3 | 0.6~1.0 | 0.15max | 0.1max | 0.1max | / | / | 0.05max | / | / | Balance |
| ZL201A | 0.2max | 0.2max | 4.8~5.3 | 0.8~1.2 | 0.05max | 0.05max | 0.05max | / | / | 0.03max | / | / | Balance |
| ZL203 | 0.3max | 0.3max | 4.0~4.5 | 0.3~0.5 | 0.1max | 0.1max | 0.1max | / | / | 0.05max | / | / | Balance |
| ZL204A | 0.05max | 0.05max | 4.6~5.3 | 0.3~0.5 | 0.02max | 0.02max | 0.02max | / | / | 0.02max | / | / | Balance |
| ZL205A | 0.06max | 0.06max | 4.6~5.3 | 0.3~0.5 | 0.02max | 0.02max | 0.02max | / | / | 0.02max | / | / | Balance |
| ZL207 | 0.5max | 0.5max | 3.5~4.5 | 0.3~0.6 | 0.5~0.8 | 0.1max | 0.1max | / | 0.15max | 0.05max | / | / | Balance |
| ZL301 | 0.3max | 0.3max | 0.1max | 0.1max | 9.5~11.5 | 0.1max | 0.1max | / | / | 0.05max | / | / | Balance |
| ZL303 | 0.5max | 0.5max | 0.1max | 0.1max | 4.5~5.5 | 0.1max | 0.1max | / | / | 0.05max | / | / | Balance |
| ZL305 | 0.3max | 0.3max | 0.1max | 0.1max | 7.5~8.5 | 0.1max | 0.1max | / | / | 0.05max | / | / | Balance |
| ZL401 | 6.0~8.0 | 0.5max | 0.1max | 0.1max | 0.1max | 0.1max | 9.0~13.0 | / | 0.1max | 0.05max | / | / | Balance |
| ZL402 | 3.0~4.0 | 0.5max | 0.1max | 0.1max | 0.1max | 0.1max | 5.0~7.0 | / | 0.1max | 0.05max | / | / | Balance |
Heat treatment states for these grades — T4, T5, T6 and what each one actually changes — are covered in heat treatment of cast aluminum alloy.
Which series applies to your process
| Process | Series | Grades quoted most | Why |
|---|---|---|---|
| High pressure 压铸 | YL | YL102, YL112, YL113 | High Si and Cu give the fluidity HPDC needs |
| Gravity / permanent mould | ZL | ZL101A, ZL104, ZL105 | Heat treatable to T6, better elongation |
| Sand casting | ZL | ZL101A, ZL104, ZL201 | Large or low-volume parts, complex cores |
| Low pressure 压铸 | ZL | ZL101A, ZL104 | Wheels and structural parts, low turbulence |
| Squeeze / semi-solid | YL or ZL | YL112, ZL101A | Depends on tool design, not on the alloy series |
Related pages
- Chinese aluminum alloy grades explained — how to pick a grade, and the ASTM / EN / JIS equivalents.
- Aluminum 压铸 — process, alloys and applications.
- Die casting: design, materials and processes — the wider engineering overview.
- How to inspect Chinese aluminum castings — checking a certificate against these limits.


